ResMed AirSense 10 Elite CPAP
Resmed AirSense 10 Elite CPAP, Click to Buy
Intuitive and easy-to-use desing lets you starting your therapy by simply plug in
the Resmed AirSense 10 Elite CPAP device and press Start.
This device has an optional HumidAirTM
integrated humidifier and optional ClimateLineTM
heated tube designed to optimise your comfort.
Intelligent detection
AutoRampTM with sleep onset detection
starts by delivering a low pressure for greater comfort and
then after you fall asleep, it gradually increases the
pressure to the prescribed therapy level. You will fall in love with this feature.
Built-in ambient light sensor
We have integrated the loving feature of the smart phones to our device,
the light level of the screen adjusts to the brightness
of the room. So if you need to get up during the night,
the screen’s back light won’t disrupt your bed partner.
You don't need to do a thing, the light also turns off automatically,
so you can settle back to sleep without disturbance.
Other features
Built-in wireless connectivity enables you to
connect your device to ResMed’s secure cloud-based
server, AirViewTM. Then your doctor can flawlessly and
securely review your therapy, adjust your device, check that your device
is working properly and troubleshoot any issues to ensure you get the
right treatment without delay.
Easy-BreatheTM motor's design philosophy is
no sound good sleep, it is whisper-quiet, offers you and your bed partner a more
peaceful and comfortable sleep.
SmartStartTM feautre is like a taxi driver
starts the car when you enter the cab, the device begins your therapy
as soon as you breathe into your mask.
When you remove your mask, it stops after a few seconds, this prevents unnecessary
air noise and lets your partner to continue sleeping peacefully.
Consistent humidification throughout the night with the
optional integrated HumidAirTM
humidifier lets your airways smoothen, with advanced HumidAir technology.
AirSense 10 Elite technical specifications
Power for 90W power supply unit
AC input range: 100-240V, 50-60Hz, 1.0 - 1.5A, Class II AC, 115V, 400Hz 1.5A, Class II (nominal for aircraft use)
DC output: 24V - 3.75A
Typical power consumption: 53W (57VA)
Peak power consumption: 104W (108VA)
Environmental conditions
Operating temperature: +5oC - +35oC (Note: The air flow for breathing produced by this therapy
device can be higher than the temperature of the room.
Under extreme ambient temperature conditions (40°C) the
device remains safe.)
Operating humidity: 10 to 95% relative humidity, non-condensing
Operating altitude: Sea level to 2,591 m; air pressure range 1013 hPa to
738 hPa
Storage and transport temperature: -20oC - +60oC
Storage and transport humidity: 5 to 95% relative humidity, non-condensing
Electromagnetic compatibility: The AirSense 10 complies with all applicable electromagnetic compatibility requirements (EMC) according to IEC60601-1-
2:2007, for residential, commercial and light industry environments. It is recommended that mobile communication devices
are kept at least 1 m away from the device.
Sensors
Pressure sensor: Internally located at device outlet, analogue gauge pressure
type, -5 to +45 cm H2O (-5 to +45 hPa)
Flow sensor:nternally located at device inlet, digital mass flow type, -70
to +180 L/min
Maximum single fault steady pressure: Device will shut down in the presence of a single fault if the steady state pressure exceeds: 30 cm H2O (30 hPa) for more than 6 sec or 40 cm H2O (40 hPa) for more than 1 sec.
Sound
SlimLine: 26.6 dBA with uncertainty of 2 dBA (Pressure level measured according to EN ISO 17510-1:2009 (CPAP mode)
Standard: 26.6 dBA with uncertainty of 2 dBA (Pressure level measured according to EN ISO 17510-1:2009 (CPAP mode)
SlimLine: 34.6 dBA with uncertainty of 2 dBA (Power level measured according to EN ISO 17510-1:2009 (CPAP mode)
Standard: 34.6 dBA with uncertainty of 2 dBA (Power level measured according to EN ISO 17510-1:2009 (CPAP mode)
Physical properties
Height: 116 mm
Width: 205 mm
Depth: 150mm
Air outlet (complies with ISO 5356-1:2004): 22 mm
Weight: 1115 g
Housing construction: Flame retardant engineering thermoplastic
Air filter
Standard: Material: Polyester non woven fibre, Average arrestance: >75% for ~7 micron dust
Hypoallergenic: Material: Acrylic and polypropylene fibres in a
polypropylene carrier, Efficiency: >98% for ~7-8 micron dust; >80% for ~0.5 micron dust
Aircraft use:ResMed confirms that device meets the Federal Aviation Administration (FAA) requirements (RTCA/DO-160, section 21, category M) for all phases of air travel.
Wireless module: 2G GSM technology, It is recommended that the device is a minimum distance of 2 cm from the body during operation. Not applicable to masks, tubes or accessories
Operating pressure range: 4 - 20 cm H2O (4 - 20 hPa)
Supplemental oxygen: Maximum 4L/min flow
Design life
Device, power supply unit: 5 years
Cleanable water tub: 2.5 years
Standard water tub, air tubing: 6 months
Manufacturer: ResMed Ltd, Australia